8/25/2023 0 Comments Traktor audio 6 routingIf you simply want to mix your old vinyl into your set, but continue using the hercules you would still benefit from owning an A6, because you would set the controller to control the software, yet use the A6 as your audio interface. If at any point you want to use a standard vinyl containing audio, you simply switch the deck in traktor to live input and you will hear the vinyl.ĭJ Tech tools has an article that show you some audio 6 set up possibilities.Īs the Audio 6 has one extra ‘main’ input and output, you can send the output from your audio mixer into the spare input on the A6 for recording to your computer and the main out, back out again to your speakers. You can therefore connect another turntable up. ![]() This uses 2 of the 6 ports on the A6 ( they say 6 in and 6 out, but they count left and right as two). The signal flows from a time-coded vinyl on the turntable to an input on the A6, converted inside of the software controlling the mp3 and sent back out of an output on the A6 to a line-in on your audio mixer. Now so long as you still have your old analogue mixer, you can hook it all up to control Traktor using timecode vinyl. The best thing I would suggest if you are wanting to continue using your turntables is to get hold of an audio 6, complete with a Traktor Scratch license. The input is a 1/4″ jack and I am unsure if it will read audio directly from a turntable as the audio 2 may not have the pre-amp necessary to work with turntables. Whilst using an aggregate device is a possibility, it will only give you one extra output and input. Take a look at the article on Native Instruments to explain how to set up aggregate audio. This is where things get complicated as you need to set up a custom audio set up on your mac to use 2 audio sources. There is however something available to mac users called aggregate audio. This is the same for the audio 2, so you are still in the same position you were previously with only the hercules. From what I understand of the hercules, this is only equipped with 2 outputs, one for the main mix and one for your headphones. Traktor unfortunately can not utilise 2 audio outputs at once, meaning that you can either set Traktor to use the Hercules Audio, or the Audio 2 interface. Unfortunately I do not have access to the devices you mention so I am unable to fully test it out for, but I will do my best to explain here how the audio routing works for Traktor and what it might require for you to get DJ’ing with your turntables again. I am happy to hear that you are getting back into DJ’ing again, it can be quite a complex space to navigate after so many changes. Or so I believe? Any help would be appreciated.” Traktor Tips’ Answer: Have I done the right thing? I can still use it to run 2 vinyl turntables through and record live mixes on my laptop. I read about not having enough outputs and that a Traktor Audio 2 would give me another 2 and get rid of any problems. I bought a Hercules Air deck system, but had trouble with distortion and good sound quality through monitor speakers. I am getting back into DJ’ing now my kids have grown up and was trying to start by mixing with mp3 files. “ I am an ageing DJ who used to DJ with turntables. I've also tried method B in the NI tutorial on NI's site by looping an RCA master out from my mixer into mixer input deck 4, but I'm not sure how to get that deck into OBS.Traktor Tips’ reader Steve (aka Ribby) asks: ![]() So I think however I make this work i need to leave "Evo 5' to maintain the use of the timecode. If I use Loopback, I can also under some settings set some sound into OBS, but only when I de-select Evo 5 audio in Traktor and select "Loopback Device." But if I select anything other than "Evo 5" on the main audio option in Traktor, I loose timecode control via the CDJs. My question is, what do I need to do to properly get audio into OBS? For example when I use iShow U, I can get youtube audio for example into my left channel of the mixer and into OBS. So the above works like a charm and all is good. I record internally in Traktor and assign to inputs 8 and 9 using the mix recorder. Outputs are also 0 and 1, and 2 and 3, respectively. I set the Traktor Audio to "Evo 5", assign external mode inputs 0 and 1 for left CDJ Deck A and inputs 2 and 3 for right CDJ Deck B. These days, I'm using a firewire to thunderbolt adaptor to connect the mixer to the MBP. The mixer was revolutionary at the time for its single firewire connection for audio. Here is my setup: Traktor Pro 3 on MBP with CDJ timecode connected to my Ecler Evo 5, an early "Traktor Certified" Mixer with a built in audio card (essentially, a version of the Audio 8 DJ). I've reviewed countless threads here and on OBS and have messed around with all of the usual options without success (Loopback, IShowU, Blackhole, etc). ![]() ![]() I need some specific instructions on how to route audio to OBS for streaming.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |